Retail Price: $210.52
Our Price: $189.47
You Save: $21.05 (10 %)
The REAL Heat 6013 3,500 Btu Marine Hydronic Fan Heater has a 3-inch outlet designed to duct airflow to an adjacent space or to accommodate tight installations. This kit includes three feet of 3-inch duct and a 3-inch grille.
|
Retail Price: $280.11
Our Price: $252.10
You Save: $28.01 (10 %)
The REAL Heat 6214 7,000 Btu Marine Hydronic Fan Heater is a 4-inch outlet heater designed to provide a greater airflow to adjacent spaces and to ease space concerns. This kit includes four feet of 4-inch duct and one 4-inch grille.
|
Retail Price: $301.33
Our Price: $271.20
You Save: $30.13 (10 %)
The REAL Heat 6414 14,000 Btu Marine Hydronic Fan Heater has a 4-inch outlet designed to duct airflow to adjacent spaces or to accommodate tight installations. This kit comes with four feet of 4-inch duct and one 4-inch grille.
|
Retail Price: $330.15
Our Price: $297.14
You Save: $33.01 (10 %)
The REAL Heat 6424 14,000 Btu Marine Hydronic Fan Heater provides two 4 inch outlets designed to split the airflow to separate spaces or to accommodate tight installations. This kit comes with six feet of 4-inch duct and two 4-inch grilles.
|
Item #77649
Furnace cement. Sealant for joints in the exhaust system. Capable for use on all systems.
|
Retail Price: $8.22
Our Price: $6.17
You Save: $2.05 (25 %)
Item #PERM-81878
Permatex Ultra Copper. High temperature RTV Sealant for joints in the flexible exhaust systems and for the bedding of exhaust thru hulls.
|
Item #W002-109
1-1/2" Stainless Horizontal outlet exhaust thru hull. Includes heat resistant gaskets. Belled on one end. For Webasto or other heaters using 1-1/2" rigid exhaust.
|
Item #W005-110
1-1/2" Stainless long exhaust elbow with condensation drain for rigid exhaust. Belled on one end. For Webasto or other marine heaters using 1-1/2" rigid exhaust.
|
Item #W001-214
1-1/2" Stainless steel rigid exhaust. Sold by the foot up to 20 feet. For Webasto or other marine heaters using 1-1/2" exhaust.
|
Item #W002-780
1-1/2" stainless steel exhaust clamp. For Webasto or other marine heaters using 1-1/2" exhaust.
|
Item #W001-441
1-1/2" Marine lace-on high temperature exhaust insulation (shown installed on exhaust tube). Available in finished lengths of 1 ft, 2 ft, 3 ft, 4 ft, and 5 ft. Specify lengths and quantities when ordering.
|
Item #001-449
1/4" USCG Approved Type A1 Fuel Hose.
|
Gar-Ber #W11BVRK
Fuel Filter KitIncludes filter housing, filter, mount bracket, valve, vacuum gauge and fittings to adapt to 1/4" hose. Other adapters available upon request.
|
Aube #TH135-01
Digital Thermostat with Day, Night and Vacation Modes Temperatures can be set individually for day, night, and vacation settings.
|
Item #W005-378K
System Heat Switch For heater system control. It can be used on all heating systems.
|
Item #W002-911.36
Hi/Low Switch with Off For one or more 12 volt fans with a total amp draw of up to 0.52 amps.
|
Item #W002-911.70
Hi/Low Switch with Off For one or more 12 volt fans with a total amp draw of up to 0.99 amps.
|
Item #W005-212-KIT
3/4" Hose Inline Aquastat For control of system fan heaters. It will keep all fans in the system off until the system reaches 110 degrees F.
|
Item #75135K-30
20 Amp Inline Manual Reset Breaker Kit A main system breaker to protect the entire heating system. Includes rubber wire boots. Per ABYC standards this should be installed within 72" of the battery connection.
|
Item #W002-103
This 9" diameter tank is made of steel and comes with 3/4" FNPT fittings, mount brackets, and 7# pressure cap. It can be used in Webasto or other marine hydronic heating systems with over 10 gallons capacity like the DBW2010.
|
Item #W002-105B
This 12" diameter tank is made of steel and comes with 3/4" FNPT fittings, mount brackets, and air bleeder. The greater volume of water your marine hydronic heating system has the less likely it will short cycle.
|
MP Pumps #MP1200-12-2015 12 Volt 15 Gallon Per Minute Shaft Drive Circulation Pump for 1" Heater Hose
Pumps 15 Gallons Per Minute of heated coolant from your Webasto or other diesel hydronic heater. For systems with up to 125 total feet of hose
|
3/4" (19.1) "Boston Bosflex" Commercial Grade Heater Hose
Reinforced specifically for use in heating systems. Rated 225 P.S.I.
Sold by the foot.
|
1" (25.4) "Boston Bosflex" Commercial Grade Heater Hose
Reinforced specifically for use in heating systems. Rated 200 P.S.I.
Sold by the foot.
|
W005-220 Mounting Shelf Bracket for DBW 2010 / DBW 2015 Powder Coated Aluminum
|
CLA-016 S/S Double Band Hose Clamp Min. 1/2" - Max. 1-1/2" Opening
300 Series Stainless Steel Band and Housing with Extended Band to Protect Clamped Surface with a 300 series Stainless Steel Deep Slotted 5/16" Hex Head Screw
|
CLA-012 S/S Double Band Hose Clamp Min. 1/2" - Max. 1-1/4" Opening
300 Series Stainless Steel Band and Housing with Extended Band to Protect Clamped Surface with a 300 series Stainless Steel Deep Slotted 5/16" Hex Head Screw
|
WSMS-2LOOPK 2 Zone Manifold 1" Hose Supply with two 3/4" Zones
|
STA-CLEAN Antifreeze - Propylene Glycol Low Silicate SCA-Precharged
Gallon
|
Coolant Treatment Kit for DBW 2010 or DBW 2015
Designed to Keep Hydronic Systems Coolant pH from Becoming Corrosive
|